Unpacking & Recovery

Your Poolside Daybed arrives as five pieces: three base panels and two bolster pillows, each vacuum sealed for safe transport.

• After opening, lay each piece flat in a well ventilated area for 48 to 72 hours to fully expand. The 120mm high density foam takes longer to recover than a standard cushion.
• Gently pat and press across the surface with both hands to help the foam open up.
• Indirect sunlight or a warm room will speed the process.
• Some minor creasing may remain after expansion. This is normal and settles with use. A fabric wrinkle release spray or a handheld steamer on the lowest setting will soften anything that lingers.

⚠ Important: Olefin fabric is heat sensitive. Always use the lowest heat setting when steaming or ironing to avoid fabric damage.

⚠ Important: Take care when cutting into the outer plastic. We recommend scissors or a blunt tipped tool rather than a sharp blade, as cutting too deep may damage the foam inside.

Assembling & Zipping

The three base panels zip together and the bolsters secure on each side, which is what holds the arched silhouette in place. The zips are hidden for a clean finish, so a little technique makes the job much easier.

• Lay all three panels flat and fully aligned before starting any zip. Most zip resistance comes from panels sitting slightly out of square, not from the zip itself.
• Start each zip from one end and travel in a single direction, easing the panels together with your free hand as you go. Never force the pull against a misaligned panel.
• Assembly and pack down are easier with two people, with one person holding the panels aligned while the other runs the zip.
• Keep the zips clear of sand and grit. Rinse them with fresh water and brush any sand away before closing. Grit dragged through a zip is the most common cause of damage.
• Rinse and dry the zips after chlorine or salt water exposure.

Cleaning

Routine cleaning:

• Spot clean with warm soapy water and a soft brush, rinse thoroughly with a hose, and allow to air dry completely.
• Rinse with fresh water after chlorine or salt water splashes. The over edge panel sits closest to the water and will need this most often.
• Rotate and swap the panel positions occasionally so wear and fade stay even across the daybed.

Sunscreen, tanning oil and insect repellent:

• Treat these as soon as you notice them. Blot with a clean cloth rather than rubbing, then wash the area with warm soapy water and rinse.
• Oil based products are the most common cause of permanent marking on outdoor fabric. Prompt attention matters more than the product you use.

For heavier stains:

• Separate the pieces and remove the cover from the affected panel only, using the zip.
• Panel covers are large. Check your machine capacity before washing, and use a commercial front loader if the load will not sit comfortably.
• Zip the cover closed, then machine wash on a gentle cold cycle, water temperature not exceeding 40°C.
• Do not bleach. Do not dry clean. Do not tumble dry.
• Lay flat to dry fully before refitting. Refitting is easier with two people.
• Iron on low heat only if required.

Moving & Storage

• Lift the panels to move them. Dragging across concrete, stone or tile will abrade the base fabric, and the underside is the part you will never think to check.
• Bring the daybed undercover in heavy rain, and always in storms. 120mm foam holds a significant amount of water and takes days to dry through.
• If a panel does get soaked, stand it on its edge with airflow on both sides and allow it to dry completely before storing or reassembling.
• Store the panels flat or upright on their edge. Avoid folding, rolling tightly or stacking heavy items on top for extended periods, as prolonged compression will set into the foam.
• Always ensure every piece is completely dry before it goes into a storage bag. Foam that is stored damp will develop odour and marking.
• When not in use for long periods, store in a cool, dry place away from prolonged UV exposure.

Important Usage Notes

Your Silux Poolside Daybed is built for poolside lounging.

• Use only for its intended purpose. Do not jump or bounce on the daybed, and do not use it as a platform for entering the pool.
• The daybed is water resistant, not waterproof, and is not designed to be submerged in water or used as a float.
• Keep the assembled daybed clear of the pool edge if children are using the area. The over edge detail is a design feature, not a barrier.
• Olefin is highly fade resistant, not fade proof. Some softening of colour over years of direct sun is normal.
• Damage resulting from misuse or inappropriate use will not be covered under the Silux Quality Guarantee.
• Dispose of all packaging thoughtfully and keep out of reach of children.

Need Help?

If you have any questions or need further support, please contact our team at:

📧 hello@silux.com.au 🌐 www.silux.com.au